초기 오픈 포커스 수정; 완전한 스펙_coverage는 아직 완료되지 않음.
1 · 실제 사용자를 위한 설계
ergonomics · specification
ib_design_technology_hl:design_users:open:1 · 2 점수
어느 것이 검증 가능한 요구 사항인가?
- 손잡이는 예쁘게 되어 있어야 한다
- 손잡이는 정의된 100 N 감시 테스트 하중을 견딜 수 있어야 한다
- 디자이너는 그것을 좋아해야 한다
정답 및 해설
손잡이는 정의된 100 N 감시 테스트 하중을 견딜 수 있어야 한다
- Choose data for the target population and task. Clearance often needs a larger-user percentile; reach may need a smaller-user percentile. A single mean dimension cannot satisfy every design constraint.
ib_design_technology_hl:design_users:open:2 · 4 점수
사용 힘은 30 N이고 선택한 안전 계수는 3이다. 목표 하중을 구하시오.
정답 및 해설
90 N
- Appropriate relation; consistent substitution; correct result; meaningful unit and interpretation.
사양은 nice하거나 strong과 같은 모호한 소망 나열이 아닙니다. 사용자 테스트는 측정 가능한 요구 사항을 평가하고 상충되는 니즈를 드러내야 합니다.
2 · 인체공학: 다양한 사용자를 포용하는 적합성
anthropometry · ergonomics
ib_design_technology_hl:design_ergonomics:open:1 · 2 점수
고정 제어 장치가 일부 의도된 사용자에게 도달 불가능할 때 가장 타당한 결정은 무엇입니까?
- 지정된 사용자 범위 내에서 더 가까운 위치 또는 조절 가능한 위치를 테스트하십시오
- 측정된 최대 도달 거리만을 사용하십시오
- 평균값이 접근을 보장한다고 가정하십시오
정답 및 해설
지정된 사용자 범위 내에서 더 가까운 위치 또는 조절 가능한 위치를 테스트하십시오
- A clearance dimension often needs to consider larger relevant body dimensions, while reach can require smaller relevant dimensions. Neither principle automatically selects a universal percentile. The measured population, posture, clothing, capability and task determine relevance. Consider physical, perceptual and cognitive demands together rather than assuming body size explains every usability issue.
ib_design_technology_hl:design_ergonomics:open:2 · 4 점수
명시된 근위 순위 방식은 ceil(p×n)을 사용합니다. p=0.90이고 n=20일 때, 순위를 구하십시오.
정답 및 해설
18 순번
- Appropriate relation; consistent substitution; correct result; meaningful unit and interpretation.
백분위수 방법은 특히 작은 샘플에서 다릅니다. 백분위수는 신체 치수의 퍼센트가 아닙니다. 평균 치수와 한 사용자의 성공적인 테스트는 접근성 있는 설계를 확립하지 못합니다.
3 · 모델, 재료 및 반복 프로토타이핑
prototype · iteration
ib_design_technology_hl:design_models:open:1 · 2 점수
스케일 외관 모델은 무엇을 직접 확립할 수 있는가?
- 완전 크기의 피로 강도
- 그 대표되는 레이아웃과 형태
- 모든 생산 비용
정답 및 해설
그 대표되는 레이아웃과 형태
- State what each model includes and omits. Compare tests with the same load, geometry and conditions. Iteration means using evidence to revise a solution and testing the revision against the original success criteria.
ib_design_technology_hl:design_models:open:2 · 4 점수
동일한 조건에서 변위가 10 mm에서 6 mm로 감소했다. 감축율을 구하시오.
정답 및 해설
40 %
- Appropriate relation; consistent substitution; correct result; meaningful unit and interpretation.
강성(elastic stiffness)은 탄성 변형에 대한 저항이며, 강도(strength)는 파단 응력을 의미합니다. 시각적으로 정확한 모델이 반드시 재료 거동을 재현할 필요는 없습니다.
4 · 제조: 공차, 변이 및 검사
tolerance · clearance
ib_design_technology_hl:design_tolerances:open:1 · 2 점수
최소 최악의 경우 간격(minimum worst-case clearance)을 결정하는 치수는 무엇입니까?
- 최소 구멍 크기 - 최대 축(shaft) 크기
- 최대 구멍 크기 - 최소 축(shaft) 크기
- 명칭 구멍 + 명칭 축
정답 및 해설
최소 구멍 크기 - 최대 축(shaft) 크기
- For a worst-case clearance model, subtract the largest shaft from the smallest hole for minimum clearance, and the smallest shaft from the largest hole for maximum clearance. The calculation assumes the stated dimensional limits and ideal geometry. Shape, alignment, temperature and measurement uncertainty can affect actual assembly.
ib_design_technology_hl:design_tolerances:open:2 · 4 점수
구멍의 크기가 12.0부터 12.4 mm이고, 축(shaft)의 크기가 11.5부터 11.8 mm일 때, 최소 간격을 계산하십시오.
정답 및 해설
0.2 mm
- Appropriate relation; consistent substitution; correct result; meaningful unit and interpretation.
더 좁은 공差的 허용 오차는 비용, 검사 시간 및 폐기물을 증가시킬 수 있으며, 사용자 Outcome을 개선하지 않을 수도 있습니다. 미세한 표시가 있는 계측 기기가 반드시 한계에 가까운 부품을 승인하기 위한 정확도를 갖춘 것은 아닙니다.
5 · 디자인 지속 가능성 및 생산 선택
design for disassembly · tolerance
ib_design_technology_hl:design_lifecycle:open:1 · 2 점수
내구성을 지지하는 것은 무엇인가?
- 모든 부품의 영구 접착
- 교체 가능한 마모 부에 대한 접근성
- 계획 없이 모든 고정 장치를 숨기는 것
정답 및 해설
교체 가능한 마모 부에 대한 접근성
- Compare a common service over a stated lifetime. Separate fixed tooling cost from cost per item. Include repair, energy, transport and realistic end-of-life pathways rather than using a recycled label as the whole judgement.
ib_design_technology_hl:design_lifecycle:open:2 · 4 점수
고정비가 400 단위만큼 차이나고 단가(변동비)가 5 단위만큼 차이난다. 손익 분점 수량을 구하시오.
정답 및 해설
80개
- Appropriate relation; consistent substitution; correct result; meaningful unit and interpretation.
저렴한 공정이 자동으로 우선시될 이유는 아닙니다. 비용 추산에는 통화, 수량 및 가정 조건이 필요하며, 프로토타입은 대량 생산 일관성을 증명하지 않습니다.