Skip to content

IGCSE Physics · June 2023 · Paper 52 · Difficulty 2 · Core

Question 1

1

In this experiment, you will investigate the stretching of a spring.

Carry out the following instructions, referring to Fig. 1.1.

(a)

The metre ruler is clamped in position near to the spring. Do not change the position of the metre ruler.

(i)

The value $l_0$ is the length of the spring when the load $L$ is $0.0\text{ N}$.

Measure the unstretched length $l_0$ of the spring. Do not include the loops at the ends of the spring in your measurement.

Record $l_0$ in $\text{cm}$ to the nearest $\text{mm}$ in Table 1.1.[1]

(ii)

Draw a diagram of the spring to show clearly the length $l_0$ of the spring.[1]

(b)

• Suspend a load $L = 1.0\text{ N}$ from the spring.

  • Record the new length $l$ of the spring in Table 1.1.
  • Calculate the extension $e$ of the spring using the equation $e = (l - l_0)$.
  • Record the value of $e$ in Table 1.1.
  • Repeat the procedure using loads $L = 2.0\text{ N}$, $3.0\text{ N}$, $4.0\text{ N}$ and $5.0\text{ N}$.
  • Record all the readings and results in Table 1.1.

Table 1.1

$L / \text{N}$$l / \text{cm}$$e / \text{cm}$
0.00
1.0
2.0
3.0
4.0
5.0

[3]

(c)

Plot a graph of $L / \text{N}$ ($y$-axis) against $e / \text{cm}$ ($x$-axis).

Draw the best-fit line.

[4]

(d)

Use the graph to determine $e_{\text{A}}$, the extension produced by a load of $2.5\text{ N}$. Show clearly on the graph how you obtained the necessary information.

$e_{\text{A}} =$ [2]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)(i)

  • Measure the length of the coils of your unloaded spring. Do not include the loops at either end.
  • Record $l_0$ in $\mathrm{cm}$ to the nearest $0.1\,\mathrm{cm}$; the value depends on your spring.

1(a)(ii)

  • Draw the unloaded spring and mark $l_0$ from the top to the bottom of its coiled section, excluding the end loops.

1(b)

  • For each load, measure the length $l$ of the coils in $\mathrm{cm}$. The lengths should increase and all be greater than $l_0$.
  • For each row, calculate the extension using $e = \mathbf{l-l_0}$. Record $e$ in $\mathrm{cm}$.

1(c)

  • Label the horizontal axis $e/\mathrm{cm}$ and the vertical axis $L/\mathrm{N}$.
  • Choose scales so the points span at least half the grid in each direction.
  • Plot all six points, including the origin, to within half a small square. Draw a thin, continuous line of best fit.

1(d)

  • From $2.5\,\mathrm{N}$ on the vertical axis, draw a horizontal line to your best-fit line, then a vertical line down to the extension axis.
  • Read $e_A$ from the horizontal axis to within half a small square and give it in $\mathrm{cm}$. The value depends on your measurements.
Original question

Log in or create account

IGCSE, A-Level & AP