Skip to content

IGCSE Physics · March 2021 · Paper 52 · Difficulty 3 · Standard

Question 1

1

In this experiment, you will investigate the motion of an oscillating metre rule.

Carry out the following instructions, referring to Fig. 1.1.

(a)

Ensure that the metre rule is horizontal. You may need to adjust the height of one of the clamps slightly.

Briefly describe how you check that the metre rule is horizontal. You may draw a diagram or add to Fig. 1.1 if it helps to explain your answer.[1]

Do not change the length $l$ of the threads during the experiment.

(b)

Move one thread to the $40.0\text{ cm}$ mark on the metre rule and one thread to the $60.0\text{ cm}$ mark on the metre rule. The distance $d$ between the threads is $20.0\text{ cm}$.

Move the stands so that the threads remain vertical.

Hold each end of the metre rule. Twist the metre rule a small amount, as shown in Fig. 1.2, and then let it go so that it oscillates in a rotating motion.

Measure, and record in Table 1.1, the time $t$ for 5 complete oscillations of the metre rule.

Repeat this procedure for $d$ values of $30.0\text{ cm}$, $40.0\text{ cm}$, $50.0\text{ cm}$ and $60.0\text{ cm}$. For each value, the threads must be at equal distances either side of the $50.0\text{ cm}$ mark on the metre rule.

Table 1.1

$d / \text{cm}$$t / \text{s}$$\frac{1}{T} / \frac{1}{\text{s}}$
$20.0$
$30.0$
$40.0$
$50.0$
$60.0$

[2]

(c)

For each value of the distance $d$, calculate and record in Table 1.1, the value of $\frac{1}{T}$ where $T$ is the time for 1 oscillation of the metre rule.

Use your values of time $t$ from Table 1.1 and the equation $\frac{1}{T} = \frac{5}{t}$.[1]

(d)

Plot a graph of distance $d / \text{cm}$ ($y$-axis) against $\frac{1}{T} / \frac{1}{\text{s}}$ ($x$-axis).

[4]

(e)

Determine the gradient $G$ of the graph. Show clearly on the graph how you obtained the necessary information.

$G =$ [1]

(f)
(i)

Explain why it is more accurate to measure the time for 5 oscillations rather than for 1 oscillation.[1]

(ii)

Describe how the experiment could be improved to make the readings more reliable.[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)

  • Measure the distance from the rule to the bench at two places. The rule is horizontal if the distances are equal.

1(b)

  • Time five complete oscillations for each distance and record all five times in seconds.
  • The times should decrease as the distance between the threads increases. The exact values depend on your apparatus.

1(c)

  • Use $\mathbf{1/T = 5/t}$ for each measured time $t$. Divide 5 by the time in seconds and record the result in $\mathrm{1/s}$.
  • The numerical values depend on your measured times.

1(d)

  • Label the horizontal axis $1/T\,/\,\mathrm{1/s}$ and the vertical axis $d\,/\,\mathrm{cm}$.
  • Choose even scales so the points occupy at least half the grid. Plot each point within half a small square.
  • Draw a thin, well-judged best-fit line through the trend of the points.

1(e)

  • Draw a large triangle on the best-fit line and read the change in $d$ and the change in $1/T$ from its corners.
  • Use $\mathbf{G = \Delta d/\Delta(1/T)}$. Divide the vertical change in $\mathrm{cm}$ by the horizontal change in $\mathrm{1/s}$. The gradient has units of $\mathrm{cm\,s}$.

1(f)(i)

  • Timing five oscillations makes the reaction-time error a smaller percentage of the measured time.

1(f)(ii)

  • Repeat each timing and calculate the mean to reduce the effect of random errors.
Original question

Log in or create account

IGCSE, A-Level & AP