Manufacture: tolerances, variation and inspection
引入| English | 释义 | 拼音 |
|---|---|---|
| tolerance/ˈtɒlərəns/ | 公差 | gōng chāi |
| inspection | 检验 | jiǎn yàn |
| clearance fit | 间隙配合 | jiàn xì pèi hé |
| quality control/ˈkwɒlɪti kənˈtrəʊl/ | 质量控制 | zhì liàng kòng zhì |
| clearance/ˈklɪərəns/ | 间隙 | jiàn xì |
A mirror wrong by 2.2 micrometres, 1990
- The Hubble Space Telescope was launched in April 1990. Its first images were blurred. The 2.4 m main mirror had been ground very precisely — to the wrong shape. Near its edge it was too flat by about 2.2 micrometres, far thinner than a human hair.
- A testing instrument had been assembled with one lens about 1.3 mm out of place, and conflicting test results were not followed up. Astronauts fitted corrective optics in 1993. Every made part varies; tolerance 公差 sets the allowed variation, and inspection 检验 checks it.
What was wrong with Hubble's main mirror in 1990?
难度 1/5 · 今日首次完成可获 100 金币及少量额外奖励
About 2.2 micrometres too flat near the edge.
Tolerances
- A dimension is written as a nominal size with limits: 10.0 ± 0.2 mm means 9.8 to 10.2 mm.
- Tighter tolerances cost more to make and inspect. Choose the loosest tolerance that still works.
What are the limits of 25.0 ± 0.1 mm?
难度 1/5 · 今日首次完成可获 100 金币及少量额外奖励
Nominal size plus or minus the tolerance.
Tighter tolerances cost more to make and inspect.
难度 1/5 · 今日首次完成可获 100 金币及少量额外奖励
Choose the loosest that works.
Fits
- Clearance fit 间隙配合: the shaft is always smaller than the hole, so it slides. Interference fit: the shaft is always larger, so it is pressed in.
- Worst cases decide the fit: smallest hole with largest shaft, and largest hole with smallest shaft.
Match each fit to its description.
难度 2/5 · 今日首次完成可获 140 金币及少量额外奖励
Worst cases decide.
Inspection and quality
- Quality control 质量控制 inspects products: gauges, callipers, sampling. Quality assurance designs the process so errors are prevented.
- Investigate conflicting measurements — Hubble's warning signs were ignored.
What is quality assurance?
难度 1/5 · 今日首次完成可获 100 金币及少量额外奖励
Quality control inspects.
Worked example: will the shaft always slide?
Hole: 9.8–10.2 mm. Shaft: 9.4–9.6 mm.
- Minimum clearance: smallest hole − largest shaft = 9.8 − 9.6 = 0.2 mm.
- Maximum clearance: largest hole − smallest shaft = 10.2 − 9.4 = 0.8 mm.
- Judgement: the minimum is positive, so every pair slides. If the design needs less than 0.5 mm of play, the tolerance must tighten, at extra cost.
A hole ranges from 8.0 to 8.3 mm and a shaft from 7.4 to 7.7 mm. What is the minimum worst-case clearance in mm?
难度 2/5 · 今日首次完成可获 140 金币及少量额外奖励
8.0 − 7.7 = 0.3 mm.
Variation in production
- Tool wear, temperature and material batches cause variation. Measure samples regularly and adjust before parts go out of tolerance.
Precise is not the same as accurate. Hubble's mirror was among the most precisely polished ever made, but to the wrong shape. Check the measuring setup, not only the measurements.
A precisely made part is always accurate.
难度 1/5 · 今日首次完成可获 100 金币及少量额外奖励
Hubble's mirror was precise but wrong.
Every part varies, so tolerances set the allowed limits. Work out fits from the worst cases, choose the loosest tolerance that works, inspect samples, and investigate conflicting measurements.
A pin of 5.00–5.05 mm must slide into a hole. Choose hole limits that give a clearance of 0.05–0.20 mm and show the worst cases.
Limits, worst cases, check.