トピック 2: 電気
AQA · GCSE · Physics トピック 2 22:46 英語のナレーション・英語と中国語の字幕を切り替え可能
章
Transcript
Why it matters.
为什么这很重要。
In 1827 Georg Simon Ohm, a mathematics teacher at a school in Cologne, published a short book in Berlin with the results of his experiments on wires.
1827 年,科隆一所学校的数学教师格奥尔格·西蒙·欧姆在柏林出版了一本小册子,介绍他对导线进行的实验结果。
He had connected wires of different lengths and thicknesses to a steady source and measured the current through each with a sensitive magnetic needle.
他将不同长度和粗细的导线连接到稳定电源上,并用灵敏的磁针测量通过每根导线的电流。
He found a simple rule: for a given wire, the current is proportional to the potential difference that drives it.
他发现了一条简单的规律:对于给定的导线,电流与驱动它的电势差成正比。
Many German scientists dismissed the work, and Ohm struggled to find a university post.
许多德国科学家对这项研究不屑一顾,欧姆也很难找到大学教职。
In 1841 the Royal Society in London awarded him its Copley Medal, its highest honour, and today the unit of resistance carries his name.
1841 年,伦敦皇家学会授予他该学会的最高荣誉科普利奖章,如今电阻的单位以他的名字命名。
Every circuit calculation in this unit starts from his rule.
本单元的每一项电路计算都从他的规律出发。
In this unit you will: AQA GCSE Physics (8463), topic 4.2 Electricity, examined on Paper 1.
在本单元中,你将学习:AQA GCSE Physics(8463),主题 4.2 电学,在 Paper 1 中考查。
It includes required practicals 3 (resistance) and 4 (I–V characteristics).
其中包括必修实验 3(电阻)和实验 4(I–V 特性)。
Static electricity is in GCSE Physics only.
静电只出现在 GCSE Physics 中。
All six equations in this unit must be learned; the Physics Equations Sheet does not list them.
本单元的全部 6 个方程式都必须记住;物理方程式表没有列出它们。
draw circuit diagrams and calculate charge, current, resistance and potential difference; investigate how resistance depends on length and how current depends on potential difference; apply the rules for series and parallel circuits;
绘制电路图,计算电荷量、电流、电阻和电势差;探究电阻如何取决于长度,以及电流如何取决于电势差;运用串联和并联电路的规律;
explain mains electricity, electrical safety, power and the National Grid; (physics only) explain static electricity and electric fields.
解释市电、用电安全、功率和国家电网;(仅物理)解释静电和电场。
Circuit diagrams use standard circuit symbols.
电路图使用标准电路符号。
Learn the symbols for a cell, battery, open and closed switch, lamp, fuse, resistor, variable resistor, ammeter, voltmeter, diode, LED, thermistor and LDR.
要掌握电池单元、电池组、断开和闭合的开关、灯泡、保险丝、电阻器、可变电阻器、电流表、电压表、二极管、LED、热敏电阻和 LDR 的符号。
An ammeter is always connected in series with a component, and a voltmeter in parallel across it.
电流表总是与元件串联,电压表则并联在元件两端。
For charge to flow, there must be a closed circuit with a source of potential difference, such as a cell.
要让电荷流动,必须有一个闭合电路,并有电池单元等电势差源。
Electric current is the rate of flow of electrical charge: Q is charge in coulombs (C), I is current in amperes (A) and t is time in seconds (s).
电流是电荷流动的速率:Q 是电荷量,单位是库仑(C),I 是电流,单位是安培(A),t 是时间,单位是秒(s)。
One ampere is one coulomb per second.
一安培就是每秒一库仑。
In a single closed loop, the current is the same at every point: a lamp transfers energy, but it does not use up charge.
在单个闭合回路中,各处的电流都相同:灯泡转移能量,但不会消耗电荷。
Worked example 1.
例题 1。
4.0 C passes a point in 2.0 s.
4.0 C 的电荷在 2.0 s 内通过某一点。
The current is I = Q over t = 4.0 over 2.0 = 2.0 A.
电流为 I = Q / t = 4.0 / 2.0 = 2.0 A。
If the same charge took 4.0 s, the current would be 4.0 over 4.0 = 1.0 A.
如果相同的电荷量用了 4.0 s,电流就是 4.0 / 4.0 = 1.0 A。
Worked example 2.
例题 2。
A charger supplies 0.90 A for 25 minutes.
充电器以 0.90 A 的电流供电 25 分钟。
Convert the time: 25 times 60 = 1500 s.
换算时间:25 × 60 = 1500 s。
Charge Q = 0.90 times 1500 = 1350 C.
电荷量 Q = 0.90 × 1500 = 1350 C。
Worked example 3.
例题 3。
A fuse wire melts when 2.0 C flows through it in 400 ms.
当 2.0 C 的电荷在 400 ms 内流过一根保险丝时,它会熔断。
Convert: 400 ms = 0.400 s.
换算:400 ms = 0.400 s。
Current I = 2.0 over 0.400 = 5.0 A.
电流 I = 2.0 / 0.400 = 5.0 A。
Using 400 s by mistake would give an answer 1000 times too small.
误用 400 s 得出的答案会小 1000 倍。
Circuit diagrams use standard circuit symbols.
电路图使用标准电路符号。
Learn the symbols for a cell, battery, open and closed switch, lamp, fuse, resistor, variable resistor, ammeter, voltmeter, diode, LED, thermistor and LDR.
要掌握电池单元、电池组、断开和闭合的开关、灯泡、保险丝、电阻器、可变电阻器、电流表、电压表、二极管、LED、热敏电阻和 LDR 的符号。
An ammeter is always connected in series with a component, and a voltmeter in parallel across it.
电流表总是与元件串联,电压表则并联在元件两端。
For charge to flow, there must be a closed circuit with a source of potential difference, such as a cell.
要让电荷流动,必须有一个闭合电路,并有电池单元等电势差源。
Electric current is the rate of flow of electrical charge:
电流是电荷流动的速率:
Circuit symbols: light arrows point into an LDR and out of an LED.
电路符号:光线箭头指向 LDR,背离 LED。
Match each part of the diagram to the text.
将图中的各部分与文字对应起来。
The current through a component depends on the potential difference across it and on its resistance: V is potential difference in volts (V), I is current in amperes and R is resistance in ohms (Ω).
流过元件的电流取决于元件两端的电势差和它的电阻:V 是电势差,单位是伏特(V),I 是电流,单位是安培,R 是电阻,单位是欧姆(Ω)。
For the same potential difference, a bigger resistance gives a smaller current.
在电势差相同的情况下,电阻越大,电流越小。
Worked example 4.
例题 4。
A potential difference of 0.45 V drives a current of 0.0075 A through a coin.
0.45 V 的电势差使 0.0075 A 的电流流过一枚硬币。
Its resistance is R = V over I = 0.45 over 0.0075 = 60 Ω.
它的电阻为 R = V / I = 0.45 / 0.0075 = 60 Ω。
Required practical 3: resistance.
必修实验 3:电阻。
Part 1 investigates how the length of a wire affects its resistance.
第 1 部分探究导线的长度如何影响其电阻。
1. Tape a resistance wire along a metre rule.
1. 用胶带将电阻丝固定在米尺旁。
Connect one crocodile clip at 0 cm and the other at the length being tested.
一只鳄鱼夹接在 0 cm 处,另一只接在所测长度处。
2. Connect a cell, switch and ammeter in series with the wire, and a voltmeter across the two clips.
2. 将电池单元、开关和电流表与电阻丝串联,并将电压表并联在两个夹子之间。
3. Record the current and potential difference for lengths from 10 cm to 100 cm, and calculate R = V over I for each.
3. 记录从 10 cm 到 100 cm 各个长度对应的电流和电势差,并分别计算 R = V / I。
4. Switch off between readings so that the wire does not heat up, because heating increases its resistance.
4. 每次读数之间都要断开开关,防止电阻丝升温,因为升温会使其电阻增大。
A graph of resistance against length is a straight line through the origin: resistance is directly proportional to length.
电阻随长度变化的图像是一条经过原点的直线:电阻与长度成正比。
If the line does not pass through the origin, check whether the length was measured from the actual contact point of the clip.
如果直线没有经过原点,要检查长度是否从夹子的实际接触点开始测量。
Part 2 compares resistors in series and in parallel.
第 2 部分比较串联和并联的电阻器。
Connect two identical resistors in series, then in parallel, and measure the total current and total potential difference each time.
先将两个相同的电阻器串联,再将它们并联,每次都测量总电流和总电势差。
Two 10 Ω resistors give 20 Ω in series but only 5 Ω in parallel.
两个 10 Ω 的电阻器串联时总电阻为 20 Ω,并联时却只有 5 Ω。
The current through a component depends on the potential difference across it and on its resistance: V is potential difference in volts (V), I is current in amperes and R is resistance in ohms (Ω).
流过元件的电流取决于元件两端的电势差和它的电阻:V 是电势差,单位是伏特(V),I 是电流,单位是安培,R 是电阻,单位是欧姆(Ω)。
For the same potential difference, a bigger resistance gives a smaller current.
在电势差相同的情况下,电阻越大,电流越小。
Worked example 4.
例题 4。
A potential difference of 0.45 V drives a current of 0.0075 A through a coin.
0.45 V 的电势差使 0.0075 A 的电流流过一枚硬币。
Required practical 3: the ammeter is in series with the wire, and the voltmeter is across the length between the clips.
必修实验 3:电流表与电阻丝串联,电压表并联在两个夹子之间的电阻丝两端。
Match each part of the diagram to the text.
将图中的各部分与文字对应起来。
Required practical 4: I–V characteristics.
必修实验 4:I–V 特性。
1. Connect the component in series with an ammeter and a variable resistor (or use a variable power supply), with a voltmeter across the component.
1. 将元件与电流表和可变电阻器串联(或使用可调电源),并将电压表并联在元件两端。
2. Change the potential difference in steps, recording the current each time.
2. 逐级改变电势差,每次记录电流。
3. Reverse the connections to the supply to get negative values.
3. 将电源的连接反过来,得到负值。
4. Plot current (vertical axis) against potential difference (horizontal axis).
4. 绘制电流(纵轴)随电势差(横轴)变化的图像。
For a diode, include a protective resistor in series so the current cannot become too large, and use a milliammeter.
对于二极管,要串联一个保护电阻,防止电流过大,并使用毫安表。
To find resistance at a point on an I–V graph, read off V and I and use R = V over I.
要找出 I–V 图像上某一点的电阻,读出 V 和 I,再使用 R = V / I。
Do not use the gradient of a curve.
不要使用曲线的斜率。
Worked example 5.
例题 5。
On a filament lamp's graph, the current is 0.16 A at 3.0 V and 0.21 A at 6.0 V.
在白炽灯的图像上,3.0 V 时电流为 0.16 A,6.0 V 时电流为 0.21 A。
At 3.0 V, R = 3.0 over 0.16 = 18.75 Ω approximately 19 Ω.
在 3.0 V 时,R = 3.0 / 0.16 = 18.75 Ω,约为 19 Ω。
At 6.0 V, R = 6.0 over 0.21 = 29 Ω. The resistance is higher at the higher potential difference because the filament is hotter. Sensors.
在 6.0 V 时,R = 6.0 / 0.21 = 29 Ω。
An ohmic conductor, such as a fixed resistor at constant temperature, has a constant resistance.
电势差较高时电阻较大,因为灯丝更热。 传感器。
The current is directly proportional to the potential difference: a straight line through the origin.
欧姆导体,例如温度恒定时的定值电阻器,电阻保持不变。 电流与电势差成正比:图像是一条经过原点的直线。
In a filament lamp, the filament gets hotter as the current increases.
在白炽灯中,电流增大时灯丝温度升高。
The ions in the metal vibrate more, so the resistance increases and the graph curves.
金属中的离子振动更剧烈,因此电阻增大,图像变成曲线。
A diode lets current flow in one direction only.
二极管只允许电流沿一个方向流动。
In the reverse direction its resistance is very high, so almost no current flows.
在反向时,它的电阻非常大,因此几乎没有电流通过。
The resistance of a thermistor decreases as its temperature increases.
热敏电阻的阻值随温度升高而减小。
It is used in thermostats.
它用于恒温器中。
The resistance of an LDR (light-dependent resistor) decreases as light intensity increases.
LDR(光敏电阻)的阻值随光照强度增大而减小。
It is used in lights that switch on automatically at night.
它用于夜间自动开启的灯。
Required practical 4: the ammeter is in series with the lamp, and the voltmeter is across it.
必修实验 4:电流表与灯泡串联,电压表并联在灯泡两端。
Match each part of the diagram to the text.
将图中的各部分与文字对应起来。
I–V characteristics of a resistor at constant temperature, a filament lamp and a diode.
恒温电阻器、白炽灯和二极管的 I–V 特性。
Read the axes and units first.
先看坐标轴和单位。
Resistance against temperature for a thermistor, and against light intensity for an LDR.
热敏电阻的阻值随温度变化的图像,以及 LDR 的阻值随光照强度变化的图像。
Read the axes and units first.
先看坐标轴和单位。
In a series circuit, the components are connected one after another in a single loop.
在串联电路中,元件在单个回路中依次连接。
In a parallel circuit, each component is on its own branch.
在并联电路中,每个元件各自在一条支路上。
Adding a resistor in series increases the total resistance, because the charge has to pass through both.
串联一个电阻器会增大总电阻,因为电荷必须通过两个电阻器。
Adding a resistor in parallel decreases the total resistance, because it gives the charge an extra path, so more current flows for the same potential difference.
并联一个电阻器会减小总电阻,因为它为电荷增加了一条路径,所以在相同电势差下会有更多电流流过。
You do not need to calculate the total resistance of resistors in parallel.
你不需要计算并联电阻器的总电阻。
Worked example 6.
例题 6。
A 6.0 V battery is connected to a 12 Ω lamp in series with a 6.0 Ω resistor.
一个 6.0 V 的电池组连接到一个 12 Ω 的灯泡和一个 6.0 Ω 的电阻器,它们串联在一起。
The two add up to 6.0 V.
两者两端的电势差加起来为 6.0 V。
The bigger resistance takes the bigger share.
电阻越大,分得的电势差越大。
Worked example 7.
例题 7。
Two 8.0 Ω resistors are connected to a 12 V supply.
两个 8.0 Ω 的电阻器连接到 12 V 电源。
In series, R_total = 16 Ω and I = 12 over 16 = 0.75 A, so each resistor has 0.75 times 8.0 = 6.0 V.
串联时,R_total = 16 Ω,I = 12 / 16 = 0.75 A,所以每个电阻器两端的电势差为 0.75 × 8.0 = 6.0 V。
In parallel, each resistor has the full 12 V, so each branch carries 12 over 8.0 = 1.5 A, and the total current is 3.0 A.
并联时,每个电阻器两端的电势差都是完整的 12 V,所以每条支路的电流为 12 / 8.0 = 1.5 A,总电流为 3.0 A。
Worked example 8.
例题 8。
A thermistor has a resistance of 80 Ω at 20 °C.
一个热敏电阻在 20 °C 时的阻值为 80 Ω。
It is in series with a 400 Ω resistor and a 12 V supply.
它与一个 400 Ω 的电阻器和一个 12 V 电源串联。
Total resistance = 480 Ω, so I = 12 over 480 = 0.025 A.
总电阻 = 480 Ω,所以 I = 12 / 480 = 0.025 A。
The potential difference across the thermistor is 0.025 times 80 = 2.0 V, and across the resistor 10 V.
热敏电阻两端的电势差为 0.025 × 80 = 2.0 V,电阻器两端为 10 V。
If the temperature rises, the thermistor's resistance falls, so it takes a smaller share of the 12 V.
如果温度升高,热敏电阻的阻值就会减小,因此它分得的 12 V 电势差会更小。
Total resistance: 12 + 6.0 = 18 Ω.
总电阻:12 + 6.0 = 18 Ω。
Current: I = 6.0 over 18 = 0.33 A.
电流:I = 6.0 / 18 = 0.33 A。
Potential difference across the lamp: 6.0 over 18 times 12 = 4.0 V; across the resistor: 6.0 over 18 times 6.0 = 2.0 V.
灯泡两端的电势差:6.0 / 18 × 12 = 4.0 V;电阻器两端:6.0 / 18 × 6.0 = 2.0 V。
The same two lamps in series and in parallel, with the meters in place.
同样的两个灯泡分别串联和并联,电表已连接到位。
Match each part of the diagram to the text.
将图中的各部分与文字对应起来。
Mains electricity in the UK is an alternating current (ac) supply: the potential difference keeps reversing direction.
英国的市电是交流电(ac):电势差的方向不断反转。
It has a frequency of 50 Hz and a potential difference of about 230 V.
它的频率为 50 Hz,电势差约为 230 V。
A battery gives a direct potential difference (dc), which always acts in the same direction.
电池提供直流电势差(dc),其方向始终相同。
Most appliances are connected to the mains with a three-core cable.
大多数电器通过三芯电缆连接到市电。
Why the live wire is dangerous.
为什么火线很危险。
The live wire is at about 230 V, and your body is at 0 V.
火线的电势约为 230 V,而人体的电势为 0 V。
If you touch it, there is a large potential difference across your body, so a current flows through you to earth, giving an electric shock that can kill.
如果你碰到火线,身体两端就会出现很大的电势差,电流会经你的身体流向大地,造成可能致命的触电。
This can happen even when a switch is off.
即使开关断开,也可能发生这种情况。
Worked example 9.
例题 9。
A lamp is switched off with a switch in the live wire.
一盏灯通过火线上的开关关闭。
Explain why point A, between the supply and the switch, is still dangerous.
解释为什么电源与开关之间的 A 点仍然很危险。
Point A is still connected to the live wire, so it is at about 230 V.
A 点仍与火线相连,所以它的电势约为 230 V。
Anyone touching it and earth at the same time has a potential difference of 230 V across them, so a current would flow through their body.
任何人如果同时接触该点和大地,身体两端就会有 230 V 的电势差,因此电流会流过身体。
Earth wire and fuse.
地线和保险丝。
If a fault connects the live wire to a metal case, a large current flows through the low-resistance earth wire.
如果故障使火线与金属外壳相连,大电流就会流过低电阻的地线。
This current melts the fuse in the live wire, which disconnects the supply, so the case does not stay live.
这股电流会熔断火线中的保险丝,从而切断电源,使外壳不会一直带电。
Mains electricity in the UK is an alternating current (ac) supply: the potential difference keeps reversing direction.
英国的市电是交流电(ac):电势差的方向不断反转。
It has a frequency of 50 Hz and a potential difference of about 230 V.
它的频率为 50 Hz,电势差约为 230 V。
A battery gives a direct potential difference (dc), which always acts in the same direction.
电池提供直流电势差(dc),其方向始终相同。
Most appliances are connected to the mains with a three-core cable.
大多数电器通过三芯电缆连接到市电。
Alternating and direct potential difference; one 50 Hz cycle lasts 20 ms.
交流和直流电势差;一个 50 Hz 的周期持续 20 ms。
Read the axes and units first.
先看坐标轴和单位。
Brown is live, blue is neutral, and green and yellow stripes is earth.
棕色是火线,蓝色是零线,黄绿相间的是地线。
Match each part of the diagram to the text.
将图中的各部分与文字对应起来。
An open switch in the live wire: point A, on the supply side, is still at about 230 V.
火线上的开关断开:电源一侧的 A 点电势仍约为 230 V。
Match each part of the diagram to the text.
将图中的各部分与文字对应起来。
Appliances transfer energy from batteries or the mains: a motor transfers energy to a kinetic store, and a heater to a thermal store.
电器从电池或市电中转移能量:电动机将能量转移为动能,加热器则将能量转移为内能。
The power of an appliance is the energy it transfers each second.
电器的功率是它每秒转移的能量。
P is power in watts, E is energy in joules and Q is charge in coulombs.
P 是功率,单位为瓦,E 是能量,单位为焦耳,Q 是电荷量,单位为库仑。
Use time in seconds.
时间要用秒。
Worked example 10.
例题 10。
A lamp carries 0.21 A at 6.0 V for 30 minutes.
一盏灯在 6.0 V 电势差下通过 0.21 A 的电流,持续 30 分钟。
Find the energy transferred.
求转移的能量。
Convert: 30 times 60 = 1800 s.
换算:30 × 60 = 1800 s。
Power P = 6.0 times 0.21 = 1.26 W, so E = 1.26 times 1800 = 2268 J approximately 2300 J.
功率 P = 6.0 × 0.21 = 1.26 W,所以 E = 1.26 × 1800 = 2268 J,约为 2300 J。
Another way: Q = 0.21 times 1800 = 378 C, and E = Q V = 378 times 6.0 = 2268 J.
另一种方法:Q = 0.21 × 1800 = 378 C,且 E = Q V = 378 × 6.0 = 2268 J。
Worked example 11.
例题 11。
A pump motor has a power of 4.86 W and a resistance of 6.0 Ω.
一个水泵电动机的功率为 4.86 W,电阻为 6.0 Ω。
Find the charge that flows in 30 minutes.
求 30 分钟内流过的电荷量。
From P = I^2 R, I^2 = 4.86 over 6.0 = 0.81, so I = root 0.81 = 0.90 A.
由 P = I^2 R,得 I^2 = 4.86 / 6.0 = 0.81,所以 I = √0.81 = 0.90 A。
Then Q = I t = 0.90 times 1800 = 1620 C.
于是 Q = I t = 0.90 × 1800 = 1620 C。
Worked example 12.
例题 12。
A 1.0 kW kettle and a 2.0 kW kettle each transfer 120 kJ.
一个 1.0 kW 的水壶和一个 2.0 kW 的水壶各转移 120 kJ 的能量。
The 1.0 kW kettle takes t = E over P = 120 000 over 1000 = 120 s; the 2.0 kW kettle takes 60 s.
1.0 kW 的水壶需要 t = E / P = 120 000 / 1000 = 120 s;2.0 kW 的水壶需要 60 s。
The more powerful kettle transfers the same energy in half the time.
功率更大的水壶转移相同的能量只需一半时间。
Appliances transfer energy from batteries or the mains: a motor transfers energy to a kinetic store, and a heater to a thermal store.
电器从电池或市电中转移能量:电动机将能量转移为动能,加热器则将能量转移为内能。
The power of an appliance is the energy it transfers each second.
电器的功率是它每秒转移的能量。
P is power in watts, E is energy in joules and Q is charge in coulombs.
P 是功率,单位为瓦,E 是能量,单位为焦耳,Q 是电荷量,单位为库仑。
Use time in seconds.
时间要用秒。
Energy against time: the 2.0 kW line is twice as steep, so it reaches 120 kJ in half the time.
能量随时间变化的图像:2.0 kW 的直线斜率是另一条的两倍,因此只需一半时间就能达到 120 kJ。
Match each part of the diagram to the text.
将图中的各部分与文字对应起来。
The National Grid is a system of cables and transformers that links power stations to consumers.
国家电网是由电缆和变压器组成的系统,将发电站与用户连接起来。
Worked example 13.
例题 13。
500 kW is sent through cables of total resistance 2.0 Ω.
通过总电阻为 2.0 Ω 的电缆输送 500 kW 的功率。
At 10 kV, the current is 500 000 over 10 000 = 50 A and the power wasted in the cables is 50^2 times 2.0 = 5000 W.
在 10 kV 时,电流为 500 000 / 10 000 = 50 A,电缆中浪费的功率为 50^2 × 2.0 = 5000 W。
At 20 kV, the current is 25 A and the power wasted is 25^2 times 2.0 = 1250 W.
在 20 kV 时,电流为 25 A,浪费的功率为 25^2 × 2.0 = 1250 W。
Doubling the potential difference halves the current and divides the wasted power by four.
电势差加倍会使电流减半,浪费的功率变为原来的四分之一。
Worked example 14.
例题 14。
A transformer has an efficiency of 0.992 and an input of 34.2 GJ.
一台变压器的效率为 0.992,输入能量为 34.2 GJ。
Useful output = 0.992 times 34.2 = 33.9 GJ.
有用输出 = 0.992 × 34.2 = 33.9 GJ。
A step-up transformer increases the potential difference from the power station to a very high value for transmission.
升压变压器将发电站输出的电势差升至很高的值,以便输电。
For the same power, a higher potential difference means a smaller current (P = V I).
在功率相同时,电势差越高,电流越小(P = V I)。
A smaller current heats the cables less (P = I^2 R), so less energy is wasted and the grid is more efficient.
电流越小,电缆发热越少(P = I^2 R),因此浪费的能量越少,电网效率越高。
A step-down transformer then decreases the potential difference to about 230 V, a safer value for homes.
然后降压变压器将电势差降至约 230 V,这个数值对于家庭来说更安全。
A higher potential difference gives a smaller current for the same power, so less energy is wasted in the cables.
在功率相同时,更高的电势差产生更小的电流,因此电缆中浪费的能量更少。
Match each part of the diagram to the text.
将图中的各部分与文字对应起来。
When two insulating materials are rubbed together, electrons are transferred from one to the other.
当两种绝缘材料相互摩擦时,电子从一种材料转移到另一种材料。
The material that gains electrons becomes negatively charged; the material that loses electrons is left with an equal positive charge.
得到电子的材料带负电;失去电子的材料则留下等量的正电荷。
Only electrons move; positive charges do not.
只有电子移动;正电荷不移动。
Charged objects exert a non-contact force on each other: like charges repel and unlike charges attract.
带电物体之间会产生非接触力:同种电荷相斥,异种电荷相吸。
A charged object has an electric field around it, a region in which another charged object feels a force.
带电物体周围有电场,在这个区域内,另一个带电物体会受到力的作用。
The field is strongest close to the object.
越靠近物体,电场越强。
Draw the field of an isolated charged sphere as straight lines pointing radially away from a positive sphere, or towards a negative one.
画孤立带电球体的电场时,用沿半径向外背离正电球体,或沿半径向内指向负电球体的直线表示电场线。
Sparks.
电火花。
As charge builds up on an object, the potential difference between it and the earth increases, and the electric field gets stronger.
随着物体上的电荷积累,它与大地之间的电势差增大,电场也变得更强。
If the field is strong enough, electrons flow through the air to an earthed conductor, producing a spark.
如果电场足够强,电子就会穿过空气流向接地导体,产生电火花。
Worked example 15.
例题 15。
A polythene rod is rubbed with a cloth and becomes negatively charged.
一根聚乙烯棒与布摩擦后带上了负电。
Explain why.
解释原因。
Electrons move from the cloth to the rod.
电子从布转移到棒上。
Electrons are negative, so the rod gains a negative charge, and the cloth is left with an equal positive charge.
电子带负电,所以棒获得负电荷,而布上留下等量的正电荷。
Worked example 16.
例题 16。
A spark transfers 0.60 J of energy with a charge of 2.0 μC.
一个电火花通过 2.0 μC 的电荷转移了 0.60 J 的能量。
Find the potential difference.
求电势差。
Convert: 2.0 muC = 2.0 times 10^-6 C.
换算:2.0 muC = 2.0 × 10^-6 C。
V = E over Q = 0.60 over 2.0 times 10^-6 = 3.0 times 10^5 V.
V = E / Q = 0.60 / 2.0 × 10^-6 = 3.0 × 10^5 V。
When two insulating materials are rubbed together, electrons are transferred from one to the other.
当两种绝缘材料相互摩擦时,电子从一种材料转移到另一种材料。
The material that gains electrons becomes negatively charged; the material that loses electrons is left with an equal positive charge.
得到电子的材料带负电;失去电子的材料则留下等量的正电荷。
Only electrons move; positive charges do not.
只有电子移动;正电荷不移动。
Charged objects exert a non-contact force on each other: like charges repel and unlike charges attract.
带电物体之间会产生非接触力:同种电荷相斥,异种电荷相吸。
Rubbing moves electrons onto the rod; the field lines of a positive sphere point radially outwards.
摩擦使电子转移到棒上;带正电球体的电场线沿半径向外。
Match each part of the diagram to the text.
将图中的各部分与文字对应起来。
AQA, GCSE Physics (8463) specification, section 4.2 Electricity, and the Required practical handbook (practicals 3 and 4).
AQA,GCSE Physics(8463)课程大纲,第 4.2 节电学,以及《必修实验手册》(实验 3 和 4)。
G. S. Ohm, Die galvanische Kette, mathematisch bearbeitet (Berlin, 1827); Royal Society, Copley Medal award, 1841.
G. S. 欧姆,《经过数学处理的伽伐尼电路》(柏林,1827);英国皇家学会,科普利奖章,1841。
AQA, GCSE Physics Paper 1 Higher, June 2022 to June 2025 (fuse, lamp, thermistor, pump, grid and spark questions, adapted).
AQA,GCSE Physics Paper 1 Higher,2022 年 6 月至 2025 年 6 月(保险丝、灯泡、热敏电阻、水泵、电网和电火花题目,改编)。
Saying a lamp uses up current.
说灯泡消耗电流。
The current is the same all round a series loop; energy is transferred.
串联回路各处的电流相同;被转移的是能量。
Putting an ammeter in parallel or a voltmeter in series.
将电流表并联或将电压表串联。
Adding parallel resistances as if they were in series.
像处理串联电阻一样将并联电阻相加。
The total is less than the smallest resistance.
总电阻小于其中最小的电阻。
Leaving current in mA or time in minutes.
电流仍用 mA 或时间仍用分钟。
Using the gradient of a curved I–V graph as the resistance.
将弯曲的 I–V 图像的斜率当作电阻。
Use R = V over I at the point.
应在该点使用 R = V / I。
Getting sensor trends backwards: thermistor resistance falls as temperature rises; LDR resistance falls as light increases.
把传感器的变化趋势说反:热敏电阻的阻值随温度升高而减小;LDR 的阻值随光照增强而减小。
Saying the earth wire carries current all the time.
说地线一直有电流通过。
Saying positive charges move when objects are rubbed.
说物体摩擦时正电荷会移动。
Only electrons move.
只有电子移动。
Current: the rate of flow of charge, in amperes.
电流:电荷流动的速率,单位为安培。
Potential difference: what drives charge round a circuit, in volts.
电势差:驱动电荷在电路中流动的因素,单位为伏特。
Resistance: opposition to current, in ohms.
电阻:对电流的阻碍作用,单位为欧姆。
Ohmic conductor: a conductor whose current is directly proportional to the potential difference at constant temperature.
欧姆导体:温度恒定时,电流与电势差成正比的导体。
Alternating current: current that keeps reversing direction.
交流电:方向不断反转的电流。
National Grid: the network of cables and transformers that links power stations to consumers.
国家电网:将发电站与用户连接起来的电缆和变压器网络。
Electric field: a region where a charged object feels a force.
电场:带电物体受到力的作用的区域。
1. 30 C flows through a lamp in 1 minute.
1. 30 C 的电荷在 1 分钟内流过一盏灯。
Calculate the current.
计算电流。
2. A 12 V supply drives 0.40 A through a resistor.
2. 一个 12 V 的电源使 0.40 A 的电流流过一个电阻器。
Calculate its resistance.
计算它的电阻。
3.
3。
コメント
コメントはまだありません。最初に質問や意見を投稿しましょう。