コンテンツへスキップ

← 国際バカロレア · IB Diploma · Design Technology · HL

復習問題

PDF ↓

オリジナル教材です。評価に使用される前に、コースのカバー範囲と貴校の現在の仕様を確認してください。

元のオープンフォーカス修正;完全な仕様カバーは未完了のまま

1 · 実際のユーザーを想定した設計

ergonomics · specification

ib_design_technology_hl:design_users:open:1 · 2 得点

検証可能な要件はどれか?

  • ハンドルは美しくなければならない
  • ハンドルは指定された100 Nの監視下テスト荷重に耐えなければならない
  • デザイナーが気に入っていること
回答と解説

ハンドルは指定された100 Nの監視下テスト荷重に耐えなければならない

  • Choose data for the target population and task. Clearance often needs a larger-user percentile; reach may need a smaller-user percentile. A single mean dimension cannot satisfy every design constraint.

ib_design_technology_hl:design_users:open:2 · 4 得点

使用力は30 N、選定された安全係数は3である。目標荷重を求めよ。

回答と解説

90 N

  • Appropriate relation; consistent substitution; correct result; meaningful unit and interpretation.

仕様書は「良い」「強い」などの曖昧な要望の羅列ではない。ユーザーテストは測定可能な要件を評価し、相反するニーズを明らかにするべきである。

2 · 人間工学:多様なユーザーへの適合

anthropometry · ergonomics

ib_design_technology_hl:design_ergonomics:open:1 · 2 得点

意図されたユーザーの一部にとって固定されたコントロールに到達できない場合、最も防衛可能な決定はどれか?

  • 指定されたユーザー範囲に対して、より近い位置または調整可能な位置をテストする
  • 測定された最大到達距離のみを使用する
  • 平均値がアクセスを保証すると仮定する
回答と解説

指定されたユーザー範囲に対して、より近い位置または調整可能な位置をテストする

  • A clearance dimension often needs to consider larger relevant body dimensions, while reach can require smaller relevant dimensions. Neither principle automatically selects a universal percentile. The measured population, posture, clothing, capability and task determine relevance. Consider physical, perceptual and cognitive demands together rather than assuming body size explains every usability issue.

ib_design_technology_hl:design_ergonomics:open:2 · 4 得点

指定されたnearest-rank法では ceil(p×n) を用いる。p=0.90、n=20 のとき、ランクを求めよ。

回答と解説

18位

  • Appropriate relation; consistent substitution; correct result; meaningful unit and interpretation.

パーセンタイル方法は様々であり、特に小規模サンプルでは差があります。パーセンタイルは体の寸法の百分率ではありません。平均寸法や、一人のユーザーによる成功したテストだけでは、アクセシブルな設計が確立されるわけではありません。

3 · モデル、材料、反復的なプロトタイピング

prototype · iteration

ib_design_technology_hl:design_models:open:1 · 2 得点

スケール外観モデルで直接確認できるものは何か?

  • 全サイズの疲労強度
  • 表現されるレイアウトと形状
  • 全生産コスト
回答と解説

表現されるレイアウトと形状

  • State what each model includes and omits. Compare tests with the same load, geometry and conditions. Iteration means using evidence to revise a solution and testing the revision against the original success criteria.

ib_design_technology_hl:design_models:open:2 · 4 得点

同等の条件下でたわみが10 mmから6 mmに減少する。減少率を求めよ。

回答と解説

40 %

  • Appropriate relation; consistent substitution; correct result; meaningful unit and interpretation.

剛性は弾性変形に対する抵抗力であり、強度は破壊応力に関わる。視覚的に正確なモデルでも材料挙動を再現する必要はない。

4 · 製造:許容差、変動、検查

tolerance · clearance

ib_design_technology_hl:design_tolerances:open:1 · 2 得点

最小の最悪ケースクリアランスを決定するのはどの寸法か?

  • 最小穴径 - 最大軸径
  • 最大穴径 - 最小軸径
  • 公称穴径 + 公称軸径
回答と解説

最小穴径 - 最大軸径

  • For a worst-case clearance model, subtract the largest shaft from the smallest hole for minimum clearance, and the smallest shaft from the largest hole for maximum clearance. The calculation assumes the stated dimensional limits and ideal geometry. Shape, alignment, temperature and measurement uncertainty can affect actual assembly.

ib_design_technology_hl:design_tolerances:open:2 · 4 得点

穴径は12.0から12.4mm、軸径は11.5から11.8mmです。最小クリアランスを計算してください。

回答と解説

0.2 mm

  • Appropriate relation; consistent substitution; correct result; meaningful unit and interpretation.

より厳しい許容差はコスト、検査時間、廃棄物を増加させる可能性があり、ユーザーへの成果向上にはつながらない場合があります。微細な表示を持つ計測装置が、必ずしも限界近くにある部品の受理に必要な精度を持っているとは限りません。

5 · 設計の持続可能性と製造上の選択

design for disassembly · tolerance

ib_design_technology_hl:design_lifecycle:open:1 · 2 得点

修理性を支持するのはどれか?

  • 各部品の永久接着
  • 交換可能な摩耗部のアクセス性
  • 計画なしにすべての固定具を隠すこと
回答と解説

交換可能な摩耗部のアクセス性

  • Compare a common service over a stated lifetime. Separate fixed tooling cost from cost per item. Include repair, energy, transport and realistic end-of-life pathways rather than using a recycled label as the whole judgement.

ib_design_technology_hl:design_lifecycle:open:2 · 4 得点

固定費は400単位の差があり、単価は5単位の差がある。損益分岐点を求めよ。

回答と解説

80個

  • Appropriate relation; consistent substitution; correct result; meaningful unit and interpretation.

安価なプロセスが自動的に好ましいわけではない。コスト見積もりには通貨単位、数量、仮定が必要であり、プロトタイプは量産の一貫性を証明するものではない。

ログインまたはアカウント作成

IGCSE, A-Level & AP