Gas models and absolute temperature
引入| English | 释义 | 拼音 |
|---|---|---|
| absolute temperature/ˈæbsəluːt ˈtemprɪtʃə/ | 绝对温度 | jué duì wēn dù |
| ideal gas/aɪˈdɪəl ɡæs/ | 理想气体 | lǐ xiǎng qì tǐ |
What would explain this observation?
- A sealed gas container changes pressure when heated. Celsius ratios cannot predict the pressure change because the gas model uses absolute temperature 绝对温度.
Build the model
- In a gas model, particles move randomly and pressure results from momentum transfer at walls.
- The ideal gas 理想气体 equation connects pressure, volume, amount and absolute temperature.
- absolute temperature: Temperature on the kelvin scale.
- ideal gas: A gas model with specified simplifying assumptions.
Which scale belongs in a gas-law temperature ratio?
难度 1/5 · 今日首次完成可获 100 金币及少量额外奖励
Gas-law ratios rest on absolute temperature measured from absolute zero, so kelvin is required. Celsius shifts the zero by 273.15 and breaks every ratio, even though a temperature DIFFERENCE is the same size in both scales.
Match each technical term to its precise meaning.
难度 2/5 · 今日首次完成可获 140 金币及少量额外奖励
Use the definitions to distinguish related quantities and processes.
Choose evidence that can test it
- At fixed amount and volume, pressure is proportional to kelvin temperature.
- At fixed temperature and amount, pressure is inversely proportional to volume.
- State which quantities are fixed before choosing a relationship.
In the lab: Use approved apparatus with a temperature range and pressure limit set by the teacher. Allow thermal equilibrium and record pressure against kelvin temperature. Never heat an improvised sealed vessel.
Which two habits make the investigation or model in this case more defensible?
难度 2/5 · 今日首次完成可获 140 金币及少量额外奖励
Stating the conditions and assumptions lets others repeat the work exactly, and recording the supporting evidence lets them check the conclusion. Hiding disagreeing results removes the evidence that could challenge a wrong conclusion, and one measurement can never establish a wider claim.
Work from known quantities
- Known: pressure is 100 kPa at 300 K, with fixed volume and amount.
- At 330 K, p2/p1=T2/T1. p2=p1 T2/T1=100×330/300=110 kPa.
- A 30 °C rise is a 30 K change, but the temperature ratio must use kelvin.
Your turn: At fixed volume, pressure is 120 kPa at 300 K. Find pressure at 350 K.
气体压强与开尔文温度
$\frac{p_2}{p_1}=\frac{T_2}{T_1}\frac{V_1}{V_2}$
气体物质的量一定时,理想气体压强随开尔文温度升高而增大,随体积增大而减小。
At fixed volume, pressure is 120 kPa at 300 K. Find pressure at 350 K.
难度 2/5 · 今日首次完成可获 140 金币及少量额外奖励
The result is 140 kPa. Known: p1 = 120 kPa at T1 = 300 K, fixed volume and amount; T2 = 350 K. Use p2/p1 = T2/T1. Rearranging: p2 = p1 x T2/T1 = 120 x 350/300 = 140 kPa. The ratio works only because both temperatures are in kelvin.
Check the conclusion and its limits
- An ideal gas is a model with conditions of validity.
- Celsius zero is not zero molecular motion, and internal energy is not determined by pressure alone.
Not true: A gas pressure ratio can always use Celsius temperatures. Ratios of temperatures are meaningful only from absolute zero. 300 K to 350 K is a ratio of 350/300; the same temperatures in Celsius, 27 and 77, give 77/27 - a different, wrong answer.
- In a gas model, particles move randomly and pressure results from momentum transfer at walls.
- At fixed amount and volume, pressure is proportional to kelvin temperature.
- Watch for: an ideal gas is a model with conditions of validity.
A gas pressure ratio can always use Celsius temperatures.
难度 1/5 · 今日首次完成可获 100 金币及少量额外奖励
Ratios of temperatures are meaningful only from absolute zero. 300 K to 350 K is a ratio of 350/300; the same temperatures in Celsius, 27 and 77, give 77/27 - a different, wrong answer.
Temperature on the kelvin scale: write the technical term.
难度 1/5 · 今日首次完成可获 100 金币及少量额外奖励
absolute temperature means Temperature on the kelvin scale.
Write from the data: find the pressure
- A fixed amount of ideal gas at constant volume has absolute pressure 90 kPa at 200 K.
- Find the pressure at 300 K. The ratio must use kelvin.
A fixed amount of ideal gas at constant volume has absolute pressure 90 kPa at 200 K. What is the pressure at 300 K, and why must the temperature ratio use kelvin?
For fixed amount and volume, PV = nRT gives P/T = nR/V, a constant. Thus P₂ = P₁T₂/T₁ = 90 × 300/200 = 135 kPa absolute. Both pressures must be absolute and both temperatures in kelvin; Celsius readings have an offset and do not give the required ratio.
For the written fixed-volume, fixed-amount gas case starting at 90 kPa and 200 K, what is the pressure at 300 K?
难度 1/5 · 今日首次完成可获 100 金币及少量额外奖励
90 times 300 divided by 200 is 135 kPa. Other options — 140 kPa (the lesson change from 120 kPa at 300 K to 350 K); 90 kPa (the starting pressure).
Define pressure and distinguish its reference zero
- Pressure is normal force divided by area, in pascals: 1 Pa = 1 N/m². A 600 N force over 0.030 m² gives an additional contact pressure of 20,000 Pa. For gas-law calculations, use absolute pressure measured relative to vacuum. A gauge commonly reports the difference between the gas and atmospheric pressures, so zero gauge pressure does not mean zero absolute gas pressure.
- All cases below are invented teaching models, using R = 8.31 J/(mol K), kB = $1.38\times10^{-23}$ J/K and NA = $6.02\times10^{23}$ per mole where needed. At atmospheric pressure 100 kPa, a tyre gauge reading 200 kPa corresponds to 300 kPa absolute. If a sealed constant-volume model warms from 280 to 308 K, absolute pressure rises to 330 kPa and the gauge reading to 230 kPa, assuming the same outside pressure.
In an invented sealed constant-volume tyre model, the gauge reads 200 kPa at 280 K and outside pressure stays 100 kPa. Find its gauge pressure at 308 K.
难度 2/5 · 今日首次完成可获 140 金币及少量额外奖励
Initial absolute pressure = 200 + 100 = 300 kPa. Final absolute pressure = 300 × 308/280 = 330 kPa. Subtract unchanged outside pressure to obtain 230 kPa gauge, not 220 kPa.
Count particles and moles without confusing molecules with atoms
- Amount of substance is $n=N/N_A$, with N the number of specified particles. One mole of oxygen gas refers to one mole of O₂ molecules, not one mole of separate oxygen atoms. A model 0.50 mol CO₂ sample contains about $3.01\times10^{23}$ molecules and has mass 22 g if molar mass is 44 g/mol. It contains three times as many atoms as molecules.
- Convert molar mass to kg/mol when combining it with SI quantities: 32 g/mol is 0.032 kg/mol. Gas mass is n times molar mass; a single molecule's mass is molar mass divided by NA. Keep lowercase n, a mole amount, distinct from uppercase N, a particle count. These symbols belong with R and kB respectively in the two equivalent gas equations.
A model .50 mol carbon-dioxide sample uses Avogadro constant 6.02 × 10²³ per mole. Find its number of CO₂ molecules, using scientific notation if needed.
难度 2/5 · 今日首次完成可获 140 金币及少量额外奖励
N = nNA = .50 × 6.02 × 10²³ = 3.01 × 10²³ molecules, about 3.0 × 10²³ to two significant figures. Its atom count is three times larger; do not count each atom as a CO₂ molecule.
Identify the fixed quantity before selecting a gas law
- For a fixed amount of ideal gas, Boyle's law keeps T constant and gives PV constant; Charles's law keeps P constant and gives V/T constant; the pressure law keeps V constant and gives P/T constant. Temperature ratios must use kelvin, and pressure ratios must use absolute pressure. Write the constraint beside the equation rather than choosing a law solely from a familiar diagram.
- A slowly compressed syringe approximates constant temperature only if energy can transfer to its surroundings sufficiently quickly. A rapid compression can heat the gas instead. A flexible balloon does not necessarily keep volume fixed, and a leaking cylinder does not keep amount fixed. If two variables change with constant amount, use the combined law rather than assuming an unstated constant temperature or pressure.
Work with Kelvin ratios and consistent units
- In an ideal constant-temperature model, 60 cm³ at 100 kPa compressed to 20 cm³ reaches 300 kPa. At constant pressure, 2.0 L at 300 K expands to about 2.67 L at 400 K. In a constant-volume tyre model whose absolute pressure is 200 kPa at 280 K, warming to 308 K gives 220 kPa. The gauge-pressure example earlier has a different initial absolute pressure and therefore a different answer.
- A sealed rigid model container at 150 kPa absolute and 20°C has T₁ about 293 K. Heating to 120°C gives T₂ about 393 K and pressure $150(393/293)\approx201$ kPa. Using 120/20 would incorrectly predict a sixfold increase. A rise of 100 Celsius degrees equals 100 K, but neither temperature ratio can be replaced by a ratio of those scale readings.
Interpret an absolute-zero extrapolation as a model
- At fixed pressure and fixed amount, the ideal relationship V proportional to kelvin T becomes a straight line against Celsius temperature. Extrapolating it backward gives an intercept near −273°C. The two curves shown use invented ideal-model points, not measured laboratory data. Different slopes can represent different sample amounts while retaining the same ideal zero-temperature intercept.
- A real sample departs from the ideal law and can condense before this extrapolated zero-volume state. The graph therefore motivates the absolute scale without claiming that a real gas has been cooled to zero volume. In an experiment, fit a valid measured range, state uncertainty in the extrapolated intercept, and do not force all measured points onto the theoretical line or erase deviations without recording them.

The illustrated constant-pressure lines use invented ideal-model points and extrapolate toward zero volume near −273°C. What does this establish?
难度 1/5 · 今日首次完成可获 100 金币及少量额外奖励
The graph is an ideal extrapolation, not a measured zero-volume state. A real experiment requires a valid range, fitted intercept and uncertainty; interactions or phase change limit the extrapolation.
Combine changes when neither pressure nor temperature is fixed
- For a fixed amount, $P_1V_1/T_1=P_2V_2/T_2$. An illustrative 50 cm³ sample at 100 kPa and 300 K is compressed to 20 cm³ while warming to 360 K. The final pressure is $100(50/20)(360/300)=300$ kPa. Include both the compression and the temperature factor; ignoring warming would give only 250 kPa.
- Matched pressure and volume units can cancel in a ratio calculation, such as kPa and cm³ on both sides, but all absolute temperatures must be in kelvin. If you use PV = nRT with the stated SI R, convert pressure to Pa and volume to m³: 1 L = .001 m³ and 1 cm³ = .000001 m³. A unit mistake can give a plausible-looking number that is a thousand or a million times wrong.
An invented fixed gas amount starts at 100 kPa absolute, 50 cm³ and 300 K. Its final volume is 20 cm³ and temperature 360 K. Find final absolute pressure.
难度 2/5 · 今日首次完成可获 140 金币及少量额外奖励
P₂ = P₁(V₁/V₂)(T₂/T₁) = 100 × (50/20) × (360/300) = 300 kPa. Temperature and volume both change; Boyle’s law alone would omit the warming.
Read paths on a pressure–volume diagram
- For a fixed amount of ideal gas, isotherms satisfy PV constant, with hotter isotherms farther from the origin. A constant-volume process is vertical on a pressure–volume plot; a constant-pressure process is horizontal. Moving along an isotherm during compression raises pressure and reduces volume while maintaining temperature, rather than making both graph coordinates rise.
- In the illustrative one-mole diagram, A has V = 10 L and T = 300 K, so P is about 249.3 kPa. Isothermal expansion to B at 40 L gives about 62.3 kPa. Heating at that fixed volume to 600 K gives about 124.7 kPa at C. Cooling at this constant pressure to 300 K halves the volume to 20 L at D. Use PV proportional to T to verify the whole path independently.

Use the ideal gas equation with the stated amount
- The two forms are $PV=nRT$ and $PV=Nk_BT$. Their constants satisfy R = NA kB; the supplied rounded numerical constants agree approximately. A model 1.0 m³ box at 100 kPa and 300 K contains about 40.1 mol, or roughly $2.4\times10^{25}$ molecules. Use unrounded intermediate values where possible and avoid pretending rounded constants determine every final digit.
- For 0.25 mol at 300 K and 120 kPa, volume is about 0.00519 m³, or 5.19 L. For an oxygen cylinder with V = 0.020 m³, P = $1.5\times10^7$ Pa and T = 290 K, the ideal estimate is about 124.5 mol and 3.98 kg. The high pressure makes checking the ideal approximation especially relevant; the calculation is not a measured mass or a guarantee that interactions are negligible.
An ideal sample has amount .25 mol, temperature 300 K and absolute pressure 120 kPa. Use R = 8.31 J/(mol K). Find volume in m³.
难度 2/5 · 今日首次完成可获 140 金币及少量额外奖励
Convert pressure to 120,000 Pa. V = nRT/P = .25 × 8.31 × 300/120,000 = .00519375 m³, about .0052 m³ or 5.2 L.
Use an ideal-gas estimate for oxygen in a .020 m³ cylinder at absolute pressure 1.5 × 10⁷ Pa and 290 K. R = 8.31 J/(mol K); molar mass .032 kg/mol. Find mass.
难度 2/5 · 今日首次完成可获 140 金币及少量额外奖励
Use PV = nRT: n = PV/(RT) = (1.5 × 10⁷ × .020)/(8.31 × 290) = 300,000/2,409.9 ≈ 124.49 mol. Mass = nM = [300,000/2,409.9] × .032 ≈ 3.98 kg, about 4.0 kg. This is an ideal-model estimate; high pressure is a reason to check its validity.
State the kinetic model's assumptions and limits
- In the simple one-species ideal model, many molecules move randomly, their own volumes are negligible compared with the container, and intermolecular forces are neglected except during very short elastic collisions. Between collisions their velocities remain constant. Elastic does not mean every molecule keeps its own speed in a collision with another molecule: total kinetic energy of the colliding pair is conserved, while individual energies can change.
- Low density makes finite molecular size and interactions less important. A temperature high enough relative to condensation helps the approximation, but “hot” alone does not establish validity at any density. At high density or near phase changes, compare measured P, V, n and T with the ideal prediction and report systematic departures. Do not use the ideal equation to describe a liquid as if it were simply a smaller-volume gas.
Obtain wall force from momentum transfer per time
- In a simplified collision-free path normal to a wall, let a molecule of mass m approach at velocity +u and rebound elastically at −u. Its momentum change is −2mu, while the wall receives impulse +2mu. For opposite walls separated by L, a return to the same wall takes 2L/u. Dividing impulse by return time gives mean wall force $mu^2/L$ for that illustrative path.
- For a three-dimensional gas, resolve velocity into wall-normal components and sum the momentum transfers from many particles. Isotropy gives equal mean squared components, leading to $P=\dfrac13\rho\overline{v^2}$. The pressure depends on momentum transfer per unit area per second. It is not determined by counting collisions alone while ignoring their momentum changes or the wall area.

Distinguish mean speed, mean squared speed and RMS speed
- The root mean square speed is $v_{\rm rms}=\sqrt{\overline{v^2}}$, not the arithmetic mean speed. For an invented set of speeds 1, 2 and 3 m/s, the mean is 2 m/s but RMS speed is about 2.16 m/s. Squaring before averaging gives positive contributions even when the vector average velocity of an isotropic gas is zero.
- Rearranging the kinetic pressure equation gives $v_{\rm rms}=\sqrt{3P/\rho}$. For a model gas at 100 kPa and density 1.2 kg/m³, this is 500 m/s. At the same pressure but density .18 kg/m³ it is about 1,291 m/s. Keep pressure in Pa, and do not replace a mean of squares by the square of a mean.
A model gas has absolute pressure 100 kPa and density .18 kg/m³. Use kinetic theory to find its root mean square molecular speed.
难度 2/5 · 今日首次完成可获 140 金币及少量额外奖励
vrms = √(3P/rho) = √(3 × 100,000/.18) ≈ 1,291 m/s, about 1.3 × 10³ m/s. Use Pa, and take the square root of the mean squared speed.
Explain the gas laws without relying on a particular box shape
- At fixed temperature, halving the volume for a fixed amount doubles number density and therefore the mean wall momentum transfer per area per second: pressure doubles. It does not universally make every molecule hit every wall twice as often. Wall-hit intervals also depend on the direction in which the container dimensions change; the density-and-momentum argument is the general one.
- Heating at fixed volume raises molecular speeds, increasing both collision frequency and momentum transfer per collision, so pressure rises. With a movable boundary and constrained external pressure, expansion reduces density until the hotter gas again matches that pressure. The relevant product is momentum flux per area, not a claim that the raw collision rate alone must return to its old value.
A fixed ideal-gas amount is compressed to half its volume at unchanged temperature. Which explanation is general rather than dependent on one particular box geometry?
难度 1/5 · 今日首次完成可获 100 金币及少量额外奖励
Fixed-temperature mean translational energy is unchanged, while N/V doubles. Pressure follows momentum transfer per area per time; individual return times and wall areas depend on geometry.
Link temperature to mean molecular energy and speed
- Combining the ideal equation with kinetic theory gives mean translational energy per molecule $\overline E_k=\dfrac32k_BT$ and RMS speed $v_{\rm rms}=\sqrt{3RT/M}$, where M is molar mass in kg/mol. At a fixed temperature, different ideal gases have the same mean translational energy per molecule, while lighter molecules have larger RMS speeds.
- At 300 K, the stated constants give about $6.21\times10^{-21}$ J of mean translational energy. Nitrogen with M = .028 kg/mol has RMS speed about 517 m/s, and helium with M = .004 kg/mol about 1,367 m/s. The speed ratio is the square root of the inverse molar-mass ratio, about 2.65. Doubling kelvin temperature doubles mean translational energy but multiplies RMS speed by only the square root of two.
Find mean translational energy per molecule of a classical ideal gas at 300 K, using kB = 1.38 × 10⁻²³ J/K. Enter joules with scientific notation if needed.
难度 2/5 · 今日首次完成可获 140 金币及少量额外奖励
Mean translational energy = 3kBT/2 = 1.5 × 1.38 × 10⁻²³ × 300 = 6.21 × 10⁻²¹ J. It depends on temperature, not molecular mass; zero is not an acceptable approximation.
For the same ideal gas, kelvin temperature doubles. What happens to mean translational energy per molecule and RMS speed?
难度 1/5 · 今日首次完成可获 100 金币及少量额外奖励
Mean translational energy is proportional to T, while vrms is proportional to √T for fixed molecular mass. Do not confuse kinetic energy’s speed-squared dependence with a linear speed law.
Reserve the three-halves internal-energy formula for the right gas
- In the simple monatomic ideal-gas model, internal energy is translational kinetic energy: $U=\dfrac32nRT$. For 3.0 mol of argon at 300 K, this gives 11,218.5 J; warming to 400 K increases U by 3,739.5 J. With fixed volume and no other work processes, the energy supplied to the gas equals this increase; at another constraint, energy can also transfer through mechanical work.
- A model 2.0 mol helium sample at 400 K has U = 9,972 J and at 800 K has twice that value. An ideal gas's lack of intermolecular potential energy does not imply that every polyatomic gas has only translational internal energy: rotational and vibrational modes can contribute. Do not apply the monatomic three-halves expression to every gas merely because PV = nRT is a useful approximation.
An invented 3.0 mol monatomic ideal-gas sample warms from 300 to 400 K. Use R = 8.31 J/(mol K). Find the increase in internal energy.
难度 2/5 · 今日首次完成可获 140 金币及少量额外奖励
ΔU = 3nRΔT/2 = 1.5 × 3.0 × 8.31 × 100 = 3,739.5 J, about 3.7 kJ. This three-halves formula is for the stated monatomic model; do not apply it to all polyatomic gases.
Design a gas-law test and check the result independently
- For a Boyle test, seal a fixed amount, record absolute pressure and total gas volume including connecting tubing, compress in steps and allow temperature to settle. Plot P against 1/V and check the expected approximately linear relationship over the model's valid range. For a pressure-law test, hold volume and amount fixed, allow uniform temperature, and plot pressure against kelvin temperature. Guard heated vessels and keep within the apparatus's rated pressure limits.
- Check leakage, pressure zero/reference, temperature equilibration, friction in a piston and systematic dead volume as well as repeated-reading uncertainty. A temperature ratio, particle-count calculation, RMS-speed relation or independent graph point can verify an answer. State which variables really stayed fixed, where the ideal model can fail, and whether a departure reflects the gas or the measuring setup before drawing a conclusion.
Explain how to solve and experimentally check a gas-law problem. Include pressure reference, model constraints, molecular explanation and an independent calculation.
A complete explanation establishes why the chosen gas equation applies and tests it against a second calculation or controlled measurement.